欢迎光临~保定八方模具 检查井钢模具

语言选择: 中文版∷  英文版

公司新闻

检查井模具的组成

作者:保定八方模具厂 本文关键词: 日期:2020/8/12 17:29:14 人气:0

保定八方检查井模具生产

壳体:由8毫米碳钢板,按直线割开制成两截.合缝间加25mm厚镀锌扁钢与壳体板电焊焊接,刨成企口缝.每半壳体有12mm厚纵筋3条及环筋6条.左右模用门铰链螺钉联接.

Shell: it is made of 8mm carbon steel plate and cut into two sections according to the straight line. A 25mm thick galvanized flat steel is added between the joint and the shell plate by electric welding, and the groove joint is planed. Each half of the shell has three 12mm thick longitudinal bars and six ring bars. The left and right molds are connected by door hinge screws

柱叉板:按柱叉设计方案规格组焊好箱型预制构件,在柱叉部位壳体上打孔用螺钉与壳体联接.检查井模具此预制构件可独立拆卸,必须留柱叉时就装上,没留柱叉时要瓶塞将壳体孔洞堵上就可以.

Column fork plate: assemble and weld the box type prefabricated components according to the design scheme and specification of the column fork, drill holes on the shell of the column fork and connect with the shell with screws. The prefabricated component of the inspection well mold can be disassembled independently, and it can be installed when the column fork must be reserved. If the column fork is not reserved, the hole of the shell can be blocked by bottle plug

跑轮及支架:跑轮及支架均用铸钢件做成.先将支架粗车后与壳体组成,总体生产加工支架外圆及壳体端板平面图,以确保跑轮与壳体的同轴度及柱内孔与柱中心线的平整度.跑轮直径600Mm,跑轮间隔2000Mm.跑轮独立生产加工后与支架用螺钉联接.

Running wheel and bracket: the running wheel and bracket are made of steel casting. The bracket is rough turned and then composed with the shell. The overall production and processing of the bracket outer circle and shell end plate plan are carried out to ensure the coaxiality between the running wheel and the shell and the flatness of the column inner hole and the column center line. The running wheel is 600mm in diameter and 2000mm in spacing. The running wheel is connected with the bracket with screws after independent production and processing

预埋孔螺丝:按设计方案孔洞规格及部位在壳体上打孔,孔外焊母丝,装上预埋孔螺丝,钉头伸进结构内的深层相当于柱头壁厚.检查井模具钉头有点光洁度有利于离心成形后拆卸.柱头三面留孔、预埋孔直徑为30mm.充分考虑没留孔的一面需有平衡块与之对称性,做到离心时的转子动平衡,因而在没留孔的一面加焊了一定净重的平衡块.

Embedded hole screw: according to the hole specification and position of the design scheme, holes are drilled on the shell, the mother wire is welded outside the hole, and the embedded hole screw is installed. The nail head extends into the deep layer of the structure, which is equivalent to the wall thickness of the column head. The screw head of the inspection well mold has a little smoothness, which is conducive to the disassembly after centrifugal forming. The diameter of the embedded hole is 30mm, In order to achieve the dynamic balance of the rotor during centrifugation, a certain net weight balance block is welded on the side without holes

堵板:离心井管为非预应力钢筋预制构件,也不是浆锚连接点、因而堵板结构极其简易,制成一块11mm厚环形平板电脑插进模端槽口内就可以.

Blocking plate: centrifugal well pipe is a prefabricated component of non prestressed steel bar, and it is not the connection point of slurry anchor. Therefore, the structure of plugging plate is extremely simple. It can be made into a 11mm thick annular flat computer and inserted into the slot at the die end

38.jpg

用手机扫描二维码 关闭
二维码